PRODUCT FEATURES

KF-S 020 Thermolock interior coating is a highly resisting coating product which is not required another coating in the interior walls as well as it isolates heat, sound and fire. Preferably it is produced as white or grey colored. Along with its longevity, it does not become deformed in the occasion of moisture or possible leakage thanks to its waterproof structure, even though it does not include water isolation because of the fact that a direct exposure to water is not possible on interior walls. It is an isolation material consisting of practically applicable structure, A1 class breathability and noninflammability

Packing Type	20 kg. Kraft Pouch
Appearance	White Granular Powder
Dry Density	380 ± %10 (kg/m3)
Thermal Conductivity	0.064 (W/mk) T1
Acoustic Insulation	25 Db
Compressive Strength	1.67 (N/mm2) CSII
Bond Strength	0,368 (N/mm2)
Fire Endurance	(1000C°)A1
Make-ready time for painting	48 Hours
Shelf Life	16 Months
Heat Range	+5C° +35C°
Application Method	Machine or Steel Trowel
Consumption	1 cm/m2 appr 4,5 - 5 kg.

POITNS TO TAKE INTO ACCOUNT 

KF-S 020, Thermolock should be used in its totality as 1 bag because of its content.
The product should be mixed with the help of a mixer or concrete mixer (for minimum 6 minutes).
Thermolock KF-S 020 interior coating should not be mixed with more water than the stated amount (15lt).
More water should not be added if waiting period of any grout prepared with Thermolock KF-S 020 takes a longer time in the boat for any reason and the grout loses its consistency. It is only necessary to mix the grout with a low speed mixer in order to renew the consistency. If Thermolock KF-S 011 applies over painted surfaces, mineral plaster and other coatings, purge the surface approximately at a rate of 70% by using paint remover chemicals, surface abrasion or other similar methods.
If Thermolock KF-S 020 applies over painted surfaces, mineral plaster and other coatings, purge the surface approximately at a rate of 70% by using paint remover chemicals, surface abrasion or other similar methods.

Place of Use:

The usage of Thermolock KF-S 020 interior coating on the interior walls especially over heat loss inhibits other construction elements (wall, column, girder etc.) from affecting the ambient temperature by absorbing the heat.  As a result of this effect, not only the energy consumption is highly economized but also heating up in winter and cooling in summer indoors are provided more quickly only by heating and cooling the indoor air.  48 hours after the application, optional satining and dyeing can be applied. It is possible to get wide range of decorative surfaces. (It is recommended to use water based paints in order not to lose the breathability feature).
 

THE PREPARATION OF THE COATING

One bag of KF-S 020 Thermolock interior coating is poured into a clean container. Approximately 15  lt of water is added and mixed with a low speed mixer for 6-7 minutes.

How to apply:

 The surface that Thermolock would be applied is cleaned from dust, dirt and similar factors. After finishing the scale of  desired main braces and angle beads, the first stage is completed by filling the main braces and angle beads with a machine or a trowel. Approximately 4 hours later the KF-S 020 Thermolock is ready for the polishing procedure. At the second stage, KF-S 020 Thermolock is applied as a 0.5 cm layer on the jigged surface with the help of a trowel. By using suitable tools for the chosen decorative surfaces (steel trowel, other kinds of trowel, roll, sponge etc.),  Other applications such as satining, dyeing and moulding can be done 48 hours after the usage of KF-S 020 Thermolock interior coating.